Fireye Controls

The D. B. Johnsen Company offers the state-of-the-art Fireye Flame Safeguard and Combustion Controls for oil, gas and non-standard fuel burners.

 

E110 FLAME MONITOR

The Fireye® E110 FLAME-MONITOR is a microprocessor based burner management control system designed to provide the proper burner sequencing, ignition and flame monitoring protection on automatically ignited burners. The device controls the operation of the combustion air blower motor and ignition and fuel valves while monitoring flame and burner interlocks to provide for proper and safe burner operation. The control also provides operating status and lockout information in the event of a safety shutdown. Click here for more information on the E110.

 

ED510 DISPLAY MODULE

The ED510 Display Module is designed to operate with the FLAME-MONITOR Burner Management Control System using the EP and remote mount style EPD programmer modules. The EP Programmers must have an Engineering code of 28 or later and the EPD programmers must have an Engineering code of 02 or later. (Note: The Engineering code is stamped on the printed circuit board along with the date code, ie: 9412-28). The ED510 display module provides the following features and capabilities: Click here for more information on the ED510.

  • Two (2) line by sixteen (16) character backlit LCD display.
  • Continuous display of burner operating status, including first out annunciation in the event of a lockout condition.
  • Three (3) key, tactile dome keypad to provide historical information of the burner, the last six (6) lockout conditions (with cycle and hour time stamp), assign messages for use with the E300 expansion module, and diagnostic messages.
  • Design mounts directly onto the front face of the EP style programmers.
  • RJ style connector for connection to the EP and EPD style programmer.
  • Remote display capability with the EP and EPD style programmers using standard DIN sized opening and remote mounting kit. Refer to Bulletin ED-8101.

 

EP160 EP161 EP165 & EP170 PROGRAMMER MODULES

The Fireye EP160, EP161 (extended MTFI), EP163 (programmable), EP170 and EP174 (early spark termination), EP165, EP166 (pilot stabilization) or EP177 (early spark termination and programmable) programmer modules are used with the FLAME-MONITOR Burner Management Control System (P/N’s E100 and E110). These programmers provide start-up programming, safe-start check, and flame monitoring supervision. They insure open damper (high purge) prepurge, proof of low fire position, and fuel valve end switch safety checks. A running interlock circuit on the FLAME-MONITOR system constantly monitors the limit switches, air flow switches, and fuel pressure switches through the programmer. The programmer control is designed to initiate a safety lockout if a problem is detected in any of these circuits. Click here for more information on programmer modules.

 

CHASSIS

E110 E100 Chassis Less Display
MEC120 MEC120 Micro M Chassis

 

WIRING BASE

60-1466-2 Wiring Base for E110
61-5042 Wiring Base for MEC120
60-1950 E300 Wiring Base
E344 E340 Wiring Base

 

AMPLIFIER

EUV1 Ultraviolet Amplifier (Use with UV1A, UV2, & UV8)
EUVS4 Ultraviolet Self-Check Amplifier (Use with 45UV5-1009)
E1R1 Infrared Auto-Check Amplifer (Use with 48PT2)
72DUV1 Ultraviolet Amplifier (Use with 70D series)
MAUV1 Ultraviolet Amplifier (Use with UV1, UV2, 45UV3)
MEUV4 Ultraviolet Amplifier (Use with UV1A, UV2, UV8A)
MEUV1 Ultraviolet Amplifier (Use with UV1A, UV2, UV8A)
72DUVS4 Ultraviolet Amplifier (Use with 45UV5-1007 - 1009)
MEUVS4 Ultraviolet Self-Check Amplifier (Use with 45UV5 Series)
MEIR4 Infrared Amplifier (Use with 48PT2)

 

To request more information or to order Fireye Controls, call the D. B. Johnsen Company Parts Department between 8:00 AM - 4:30 PM EST at 1-800-442-1242 or click here to email us.